Jump to content
Click here to check out this guide

FAQs | Repair Videos | Academy | Newsletter | Contact


DISCLOSURE: We may earn a commission when you use one of our coupons/links to make a purchase.
  • Upcoming Events

    • 30 March 2024 02:00 PM Until 03:00 PM
      0  
      All Appliantology tech members are invited to join in this workshop on all things Appliantological: bidness, customers, tools, troubleshooting, flavorite brewski, whatever. Webcams and microphones are open and live!
      This workshop is also a great time for any students at Master Samurai Tech to bring any and all questions about the coursework. We're happy to walk through any concepts you're having trouble with. Think of it like office hours with your teachers. 
      If you have a specific appliance problem you'd like us to talk about, post it here! We need a problem statement and a PDF of the tech sheet or schematic so we can all see it on screen share. If you have a PDF that isn't already in the File library here at Appliantology, send it to us by attaching it to the contact form. 
      Also, follow this Calendar Event so you'll get notified of new posts here. Look for the "Follow" button either at the top of the topic on desktop or below the topic on mobile.
      Who: This workshop is only available to tech members at Appliantology.
      When: Saturday, March 30 @10:00 AM Eastern Time.
      Where: Online via Zoom
      How:
      Click here to go to the forum topic with the registration link. If you're interested, register now. Arrive a couple minutes early to make sure your connection is working. Set a reminder for yourself for this workshop so you don’t miss it.  And check out past workshops here: https://appliantology.org/announcement/33-webinar-recordings-index-page/

MFI2266AEB Maytag French Door


megadan66

Recommended Posts

Can someone tell me how to get the freezer door out of this Ref. And also what to do if you put in a new mother board and it won't reprogram itself after following tech sheet instructions. Customer had new board and someone else working on this before me. Original problem is evaporator icing up........Thanx

Link to comment
Share on other sites

  • Replies 5
  • Created
  • Last Reply

Top Posters In This Topic

  • megadan66

    3

  • RegUS_PatOff

    2

  • certified tech group 51

    1

Door Removal

Freezer Drawer

1. Open drawer to fully open position.

2. Remove upper and lower baskets.

3. Remove screws one in each rail marked on side of rail.

4. Lift front of drawer up and out to remove drawer.

5. Set drawer on a padded surface to prevent damage to finish.

Link to comment
Share on other sites

... it won't go into forced defrost mode and heater and terminator check fine ?

that would indicate a bad Controller . . . OR wiring

May have to do some voltage tests while in the Defrost mode.

Did you get the new Controller to "program" ?

OR how far did you get in the programming ?

Programming Mode:

NOTE: The Program Code is located on the Serial Plate on this unit after the word Code.

1. Press and hold the Door Alarm Keypad DoorAlarm .

2. Press and hold Freezer Temperature Down Keypad .

3. Release the Door Alarm Keypad DoorAlarm and wait 3 seconds.

4. The control will display PE to indicate the programming mode.

5. Entry is confirmed by pressing the Freezer Temperature Down Keypad once more.

6. The control will display the current Program CODE. This value should be validated with the Program CODE printed on the unit serial plate.

NOTE: If the Program CODE is correct, the Programming Mode is exited by pressing Door Alarm Keypad for 3 seconds.

7. Press the Refrigerator Temperature Up Keypad or Refrigerator Down Keypad to change the digit value with each key press.

8. The decimal point indicates the selected digit. Press the Freezer Temperature Up Keypad to select the next digit.

9. Once the desired Program CODE is entered, press and hold the Freezer Temperature Down Keypad until the Program CODE begins flashing indicating it has been saved.

Link to comment
Share on other sites

All the way through with the programming but just beeps at the end and I believe went back to all 0's. The board I replaced was the one in the back of the Ref. Is this the control board. Because I know theres another board in the frezzer door behind the touch pad. Right ?

Link to comment
Share on other sites

  • 1 month later...

Lets get a few things straight.. :huh: ..........You replace the board in the rear ... The High voltage board....correct ??? Board in the freezer door???... :kopkrab: ...freezer door is the drawer door...Do you mean the left fresh food door ?? the one with the dispenser, the one with the low voltage board ??? you stated "customer had new board" what did the customer do with the "new board " ???....keep us posted....

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
×
×
  • Create New...